Notebook HP Omnibook XE3 - Service manuals and Schematics, Disassembly / Assembly. Invalid Serial Number Hp Bios. Download Free.

HP Pavilion zt1100/xz100 Omnibook xt1000 Removal and Replacement 2-19 Figure 2-15. Removing the Display (2) Reassembly Notes • While installing the hinge screws, support the display so that it remains approximately flat. • Make sure the cable fits into its slot in the bottom case, and reinsert the cable into the retaining clip near the left display hinge. • Make sure the tabs on the left side of the left speaker fit between the corresponding tabs in the bottom case, and the speaker wires fit through their notch in the bottom case. Screw, M2×4mm Screws, M2×4mm (2).

2-20 Removal and Replacement HP Pavilion zt1100/xz100 Omnibook xt1000 Removing Display Assembly Components (HP Authorized Service Providers Only) Note This procedure describes how to remove the display bezel, the inverter PCA, and (if present) the wireless antenna. Although these components can be replaced individually, in many cases it is preferable to replace the display assembly as a unit. Required Equipment • #0 Phillips screwdriver. Removal Procedure 1. Unplug the AC adapter, if present, and remove the battery. Remove these additional assemblies: • Keyboard cover (page 2-9).

• Display assembly (page 2-18). Use a screwdriver or similar object to carefully pry the screw covers from the display bezel. Remove the four screws from the display bezel.

Beginning at the top center of the display, carefully pry up the inner edge of the bezel with thumbs and fingers. Work your way around the inside edge to unsnap the latches, then remove the bezel from the display. Remove the retaining screw from the inverter PCA. Carefully turn the PCA over, unplug the cable from the left end, and disconnect the wires extending from its right end. If present, remove both retaining screws from the Bluetooth or 802.11b antenna, and remove the antenna from the display. HP Pavilion zt1100/xz100 Omnibook xt1000 Removal and Replacement 2-21 Figure 2-16. Removing Display Assembly Components Reassembly Notes • Make sure the alignment hole in the inverter PCA fits over the corresponding post in the display case.

• Make sure the alignment hole in the wireless antenna fits over the corresponding post in the display case. • Set the bezel in place on the display, then work your way around the bezel, firmly snapping the bezel latches shut.

• The rounded screw covers go on the screws at the top of the display bezel, and the flat covers go on the screws at the bottom of the bezel. Canon Vixia Hf10 Usb Driver more. Screw, M2×4mm Screws, M2×4mm (2) Screws, M2×4mm (2) Screws, M2.5x6mm (4) Inverter PCA Bluetooth antenna 802.11b antenna.

2-22 Removal and Replacement HP Pavilion zt1100/xz100 Omnibook xt1000 Removing the Fan and Heatsink (HP Authorized Service Providers Only) Required Equipment • #0 Phillips screwdriver. Removal Procedure 1.

Unplug the AC adapter, if present, and remove the battery. Remove these additional assemblies: • Keyboard cover (page 2-9). Canon Eos 350d Time Lapse Software. Hp Scanjet G3010 Driver For Windows Xp Free Download. • Keyboard (page 2-11).

Remove the retaining screw from the right speaker. Disconnect the speaker wires from the motherboard, and lift the speaker out of the notebook. Disconnect the fan wires from the motherboard.

Remove both retaining screws from the fan. Lift the fan out of the notebook. Caution Do not spin the fan blades with your finger, or you could damage the fan’s bearings. Remove the heatsink’s four retaining screws (with springs attached). Lift the heatsink out of the notebook. 2-24 Removal and Replacement HP Pavilion zt1100/xz100 Omnibook xt1000 Reassembly Notes • Make sure the fan wires are not pinned under the fan, and is securely plugged into its socket. • If present, make sure the wireless cables are not trapped under or behind the fan, or beneath the cooling fins.